Posts Tagged ‘Maple Ridge’

Troubleshooting Drain Problems: Some Pointers from Delta

Monday, November 21st, 2011

It’s Saturday afternoon in Delta and you are preparing dinner for a number of guests. The kitchen is packed with groceries and you start to clean a lot of veggies for dipping. But there is a problem. The drain in your kitchen sink is “acting funny.” It drains slowly and is making a gurgling sound. In fact, it’s beginning to smelly funny, too.

The timing couldn’t be worse. Before you hit the panic button, let’s take a moment to troubleshoot the problem. Maybe it isn’t much of a problem after all.

First of all, is the problem confined to just the kitchen sink? There may be similar problems in other sinks, which would indicate a larger problem with the plumbing in your home. Hopefully, the kitchen sink is the only area you need to be concerned with.

Next, if you have a two-basin sink who should check to see if both sides are clogged or just one. Remove all dishes and utensils and run water on both sides. If water drains from one and not the other, there is a clog somewhere in the pipe leading to the union of both pipes. You have now centralized the drain problem. If both sides back up, the clog is further down the pipe. But it is still not a big problem.

One way to troubleshoot for drain problems is to simply run very hot water down the drain. This tends to break up clogs of grease by melting it away. The fix can also be as simple as running the garbage disposal long enough to dislodge any debris. You may even want to grind up some food you were planning to dispose of or take some lettuce greens and use the disposal on them. If this food takes a long time to grind or doesn’t at all, the disposal may be the culprit, leading to blocked drains.

And if you are preparing for your party by taking a shower and the shower drain is acting funny, don’t hit the panic button just yet. You may just have a build-up of hair or skin on the drain cover or screen. Use you foot to swish around the water and if water drains more quickly when you do this, the fix can be as simple as reaching down and picking up the debris. Having a plunger nearby helps, too.

None of this is brain surgery and quick fixes are easy to do. But if the problem persists and you don’t have the time or patience to work on your drain problem, call a plumbing professional – and stick with your party plans.

Tags: , , , ,
Posted in Plumbing | Comments Off

Possible Causes of Poor Heating Performance from Your Boiler: Some Pointers from Langley

Friday, October 21st, 2011

You don’t have to be a rocket scientist or a mechanical engineer to troubleshoot – and possibly diagnose – the problems with your boiler when its heating performance is erratic or non-existent in your Langley home.

The good thing about boilers is that they are typically reliable and long-lasting. There aren’t a lot of working parts that can break down and cause problems, compared to other home heating equipment. When problems do arise, they are usually related to the expansion tank or circulating pumps. But a problem can be much simpler – like a tripped circuit breaker.

The most common problems can be noise, no heat, or poor/erratic heating. Before calling a qualified heating and cooling professional, take a moment to see if you can figure out the what’s wrong.

If you have a noisy boiler it might be because of two things – a faulty circulating pump or water trapped in the return lines. If the pump breaks it will make a loud noise when its motor runs. Water can be trapped in the return lines, which may require “re-pitching” the lines to allow for a flow back to the boiler. You may be able to adjust the flow by positioning hangers on the piping but replacing a pump is better left to a professional.

If your boiler is producing no heat, it could be because of something as simple as a circuit breaker being tripped or a fuse being blown. Check your circuit breakers and fuse and reset or replace if necessary. Is your boiler thermostat in the heat mode? It should be but if it isn’t, make the switch. If your boiler has a standing pilot you should check to see if it is lit and if not, re-light it.

Other problems would take a professional to fix. For example, no heat can be traced to low water levels in the boiler. The boiler should always be half-full of water and if it isn’t, it is likely because of leaks or a faulty pressure reducing valve. Don’t try and fix the problem by yourself.

Low water levels may not cause the boiler to lose its heating capabilities, but may cause fluctuations in its heating capacity. Again, it is advisable to call a professional to diagnose and fix the problem. Poor heating can also be traced to mineral deposits in the boiler. Consult your owner’s manual on instructions how to flush out the boiler.

As always, read the owner guide or operating manual for your boiler. You should get some good tips on proper maintenance and troubleshooting. And have the phone number of a qualified professional taped to your boiler – just in case.

Tags: , , , , , ,
Posted in Heating | Comments Off

What’s the Difference Between a Furnace and a Boiler? A Question From Ruby Creek

Wednesday, October 5th, 2011

When it comes time to choose a new heating system for your Ruby Creek home, there is a good chance your choices are limited. Most homes already have either forced air or radiant heat equipment installed so choosing something different would be costly and unnecessary. But, if you have a choice or are moving into a new home, here are some things to consider regarding the difference between furnaces and boilers.

What a Furnace Does

A furnace uses a fuel like gas, oil or electricity to heat a series of coils in the device. The furnace then uses a blower to push air across the heated coil and into an air handler where it can be distributed throughout your home. This is called a forced air system and requires a combination of ducts and filters to keep air moving smoothly and cleanly throughout your home.

If you have access to gas, a gas furnace with an AFUE of 90% or higher is one of the most efficient and cost effective ways to heat your home. These furnaces can also last upwards of 20-25 years with proper maintenance.

What a Boiler Does

A boiler is different in that it uses water as the heat carrying medium, not air. Boilers still need gas, oil or electricity to heat up the water in the system, though they often use less of it than a traditional furnace – depending on the age of the furnace and the boiler. After water is heated in the boiler, your radiant heating system carries the water to baseboard heaters or radiators throughout your home. This form of heat is preferred by many because it doesn’t require ductwork (which requires extra maintenance) or extra air filtering and it is more humidity friendly in a large home.

In terms of efficiency, both boilers and furnaces are efficient if you’re buying a new model. Capacity is also evenly matched.

Tags: , , , , ,
Posted in Heating | Comments Off

Installing Drainage System: Why Call a Burnaby Plumber?

Friday, August 12th, 2011

A proper drainage system is a great asset when you are trying to improve the appearance of your Burnaby lawn or increase your landscaping options. A lawn that does not drain right will have dry and wet spots that make it difficult for plants to grow. Your lawn will develop a spotty appearance because of these types of areas and you will probably also have a smaller area to work with in general.

With a good drainage system, on the other hand, you can make use of your entire yard. As long as water can reach all areas but does not linger too long in any one of them, all of your plants should be able to grow nicely. This is often a project that handymen are inclined to take on themselves, but there are several potential pitfalls when you do. It may not seem all that complicated to put in a drainage system, but you do need to know what you are doing if you want to get the job done right.

In order to function properly, a drainage system needs to be installed on a slope. Water will always run downhill, so making your drainage system run downhill will ensure that gravity will do all the work for you. If the proper slope is not maintained, however, there are plenty of areas where water can pool.

That is exactly the type of situation you are trying to avoid by putting the drainage system in, so all of your hard work could be for nothing if you do not get the slope calculated correctly. While this type of measurement and calculation can be challenging for you, it is second nature to a professional plumber. Hiring an expert to help you with this area of your drainage system is the best way to make sure you have the right setup planned.

You will also need to know where to lay out the drainage system. This involves analyzing the sources of water in your yard and understanding what you need to do to move it from one area to another. Again, this can be a challenging if not overwhelming aspect of the project for a layman, but for a professional it is simply part of the job.

On top of all of that planning, you will need to have the right tools and materials to put the drainage system together. Plumbers already have all of this on hand and they know which tool to use when. Your project will go much more smoothly and you will be assured of much better results if you use a professional to install your drainage system.

Tags: , , , ,
Posted in Plumbing | Comments Off

Filters

Wednesday, July 6th, 2011

Installing air filters in your home is a great way to make sure the air your family breathes every day is safe and free of contaminants. But you shouldn’t just go out and buy the first air filter you see. When it comes to quality air filtration, HEPA filters are the industry leaders, and for good reason. They can remove up to 99.97% of indoor air contaminants that measure 0.3 microns or larger, a phenomenal success rate unmatched by any other filters on the market.

Proper HEPA Filter Practices

To be effective, even HEPA filters need to be installed and maintained properly. Consulting with an HVAC professional is the best way to ensure that the air filtration system you get is completely compatible with your home heating and cooling system. The filter must also be installed in the appropriate place so it can catch the most contaminants. Especially if you have a forced air heating and cooling system, there are a lot of potential locations for your filters. A good HVAC professional can help you determine which spots will serve you best.

Changing Your HEPA Filters

Once your filtration system is in place, you should maintain it properly so it continues to catch and remove all those unwanted particles from your indoor air. Keeping up with the proper filter changing schedule is a big part of this. Every HEPA filter comes with manufacturer’s recommendations on how often the filter needs to be changed. Prefilters often need to be changed more often, sometimes even once every 90 days, so you should find out if your system has one of these as well.

Many HEPA filters only need to be changed once every year or two, but the conditions in your home can make it necessary to change them more often. For example, if your home has a lot of dust or other specific air contaminants, you may need to change your HEPA filter as often as once a year.

Both HEPA filters and prefilters are quite easy to remove and replace. If you’re not sure how to do it, have your technician show you the next time they come out for a routine maintenance visit or when they put install the system. As long as you replace your filters regularly, you should have no trouble maintaining high indoor air quality with a HEPA air filtration system.

Tags: , , ,
Posted in Indoor Air Quality | Comments Off

Touch-Free Faucets: Green Plumbing That’s Fun and Easy!

Wednesday, December 8th, 2010

One fun, high-tech, and relatively inexpensive way to go green is to install a touch-free faucet in your kitchen or bathroom. Touch-free faucets work on a very simple principle: when you’re not actively using them, they shut off. There are a lot of times when you leave a normal faucet on simply because your hands are full (i.e. when you’re washing something), or soapy. With a touch-free faucet, the water turns off during all these gaps in your actual water usage. According to industry estimates, the result can be a water savings of up to 70%.

Of course, most of us have encountered touch-free faucets in public restrooms, and they can be frustrating. You can end up waving your hands around wildly, hoping a faucet somewhere in the room will turn on, and then the water cuts off mid-stream, just when your hands are full of soap. However, new sensor technology is making touch-free faucets much easier to use. These sensors are “omni-directional”, meaning that when your hands are anywhere within a given radius around the tap, the water will turn on and stay on.

Top-of-the-line models can dispense filtered water for drinking, and one designer model has a digital LED screen that allows you to adjust the water temperature, fill a glass with drinking water, or dispense dishwashing detergent, soap, or even hand lotion – all by waving your hand in front of the desired function. Some models also have manual override, which enables you to push a button so that the faucet will stay on for a certain time period without shutting off, even if you move your hands away.

Alternatively, if you like your current faucet and want to keep it, you can add a touch-free faucet adaptor to your existing faucet. Adaptors start at about $50.

Touch-free faucets and adaptors are surprisingly easy to install – no more difficult than conventional faucets. They can be powered by an AC adaptor or batteries, so you can install them almost anywhere.

In addition to the water savings, there are other benefits to touch-free faucets as well:

  • Touch-free faucets are much easier to use than regular faucets – especially if your hands are dirty, soapy, or full.
  • Touch-free faucets are much more sanitary than conventional faucets. With conventional faucets, you turn them on with dirty hands, wash your hands carefully, and then immediately touch the dirty handles again to turn off the faucet.
  • Touch-free faucets allow you to set the water temperature precisely for improved comfort and safety.
  • Touch-free faucets are ADA compliant for people with disabilities.
  • Touch-free faucets are helpful for older people or small children who may forget to turn off the faucet when they are finished
  • Kids love touch-free faucets – no more arguments about hand-washing!
  • Touch-free faucets make your bathroom or kitchen look really cool and high-tech.

Tags: , , , ,
Posted in Plumbing, Water Conservation | Comments Off