Posts Tagged ‘Plumbing Repair’

« Older Entries

New Westminster Plumbing Guide: What to Do if a Pipe Bursts

Wednesday, January 25th, 2012

If you live in a cold climate, you are more likely to have experienced the disaster of a frozen pipe bursting. There are other causes of burst pipes, so rest assured you are not alone; plenty of New Westminster homeowners have had to face a burst pipe as well.

When this happens, there are three fronts on which to attack the problem: stopping the flooding, repairing the pipes and preventing future bursts.

Before doing anything else, you need to stop the flooding in your house. Start by turning off the water supply, either to that pipe or to the whole house. It doesn’t matter which, as long as it’s shut off. Turn on cold water taps around the house to drain remaining water from the pipes. Turn off the water heater. This will at least prevent the flood damage from being too extensive.

Get a sump pump and or some absorbent material to start sopping up the water that leaked into your home, then call a plumber. The pipe and fitting will need to be replaced, and some adjacent ones may need to be as well, so the best solution here is just to call in a professional rather than try to do it yourself. The last thing you need is another burst pipe.

Finally, prevent future breaks in pipes by implementing some of these strategies:

  • Insulate your pipes
  • On cold days, keep your pipes warmer by opening up doors to the attic or basement
  • When going away in the winter, shut off the water supply and drain the plumbing system

By keeping your pipes as warm and insulated as possible, you decrease the likelihood that the water within will freeze, potentially causing a leak or break in the pipe. Burst pipes are not necessarily completely preventable, so it is important that you now know what to do if and when a pipe bursts in your New Westminster home.

Water damage, especially flooding, can cause serious trouble in your home, so everything you can do to prevent and mitigate the risk is a good step.

Tags: , , , , ,
Posted in Plumbing | Comments Off

Burnaby Plumbing Repair Question: Why Is My Toilet Dry and How Can I Fix It?

Monday, January 23rd, 2012

Under normal circumstances, after you flush your Burnaby home’s toilet, the tank and bowl both fill back up with water, preparing it for the next use. The water from the tank is what flushes into the bowl when you push the handle, so if it is not filling properly, then the toilet will be dry.

This problem is troublesome, but not uncommon. It has a number of possible causes and fixes.

The first place to look is the water supply to the tank. If it has been inadvertently turned off, then obviously the tank will not fill. This is akin to the troubleshooting section of your old VCR manual, where it tells you to make sure the power cord is plugged in. It may sound silly, but it never hurts to check the most obvious and easily fixed of the possible causes first.

Another possibility that is very easy to fix is that the ballcock inside the tank has jammed at the top. Inside your toilet tank is a rubberized bulb connected to an arm. This bulb floats in water and controls the intake valve on the toilet tank. So, when the water level reaches a certain depth, the ballcock floats and closes the valve. However, if the ballcock is jammed in an upward position, it would keep the valve closed even if the tank is empty.

In this case, it may just be a matter of pushing the ballcock past the jam and then making sure it moves up and down freely. That alone may fix it.

A third common cause of the dry toilet problem is a clogged intake valve beneath the toilet. These valves can become clogged and then not allow water through, especially in systems with hard water or particularly old pipes.

If this is the problem – or if it is anything besides one of the two simple fixes described above – the best solution is to call a plumber. A Burnaby professional can correctly identify the source of the problem and perform the necessary repairs. It’s likely not going to be a huge repair, but it’s best to entrust the job to a pro.

Tags: , , , , ,
Posted in Plumbing | Comments Off

Vancouver Plumber’s Guide: Detecting Leaks with Your Water Meter

Friday, January 20th, 2012

When you notice a leak in your Vancouver home, you fix it right away, but what happens when you don’t notice a leak for days or even weeks? The damage it causes can have a profound impact on your water bill and the good repair of your home. To avoid hidden leaks – the ones that hide in your walls or your yard, keep a close eye on your water meter.

The Hidden Leaks

Obvious leaks are…well, they’re obvious. They pour water down the walls, leave puddles in your bathroom or create ponds in your backyard. Unfortunately, the majority of leaks are much less obvious. They result from small drips between pipe joints in your walls or a hairline fracture in your water main or drain pipes. They may not even appear where you can see them.

If this happens, it’s important to have a keen eye for the signs that a water leak has occurred. Specifically, look for jumps in your water meter readings.

Watching the Water Meter

Your water meter tracks every drop of water consumed by your family. To check for water loss, record the reading at the same time every day and watch how it changes. To be sure of a leak, you can turn off all the fixtures in your home and watch for the meter to move. If the meter moves despite the fact that no one in your home is consuming any water, it is likely a leak.

You can also compare your bills from one month to the next. If your bill rises suddenly, without any clear reason, check the meter readings and the rates. If the meter reading increased suddenly and the water rate did not, there might be a leak to blame. If that’s the case, call a professional to inspect your water lines immediately – what is hidden to you might be a relatively obvious, straightforward repair to someone else.

Tags: , , ,
Posted in Plumbing | Comments Off

Surrey Plumbing Repair Guide: How to Plunge a Clogged Drain

Monday, January 16th, 2012

It is almost inevitable that you will have to deal with a plugged drain somewhere in your Surrey home at some point. This drain may be in the bathtub, a sink or a toilet. But wherever it is, a plunger is usually your best bet for getting it out. If you are going to be successful, though, you need to know how to set yourself up and use the plunger properly.

To begin with, remove the strainer or pop-up plug from the opening of the drain. You want the material that is clogging the drain to be able to come back up through that hole when you apply the plunger suction. Next, make sure the sink or tub has enough water in it to cover the head of the plunger completely. A toilet generally has enough water in it already. This water helps to create a better seal for the plunger and allows you to generate better suction, both of which are essential if you are going to dislodge that plug.

You should also make sure you block off any other outlet connected to the drain you are going to plunge. To do this, stuff an old rag or sponge into the overflow opening or into the second drain of a two compartment sink. That will make it possible for the entire force of your suctioning to reach the clog because it will not be compromised by air escaping through an alternate opening.

Now you are ready to plunge. Place the plunger over the opening of the clogged drain. While keeping constant contact with the sink or tub floor, move the plunger rapidly up and down between 10 and 20 times. After the last plunge, pull the plunger off of the sink or tub floor quickly. This should break the seal you have established and help to pull the clog back up the drain towards you.

It can take a few cycles like this before you are able to dislodge the clog completely. But each time you plunge, you are doing more to break up the clog. The pressure from the plunger can eventually get rid of many difficult clogs, so do not be discouraged if it takes a few tries. If you are still having problems, call your local plumber.

Tags: , , , ,
Posted in Plumbing | Comments Off

North Vancouver Plumbing Question: Why Does My Sink Backup When I Run the Washing Machine?

Friday, January 13th, 2012

Every now and then something strange happens that is simultaneously baffling and frustrating. Gray water from your washing machine backing up into your sink is one such problem and for many North Vancouver homeowners it can be an ongoing source of annoyance.

Why does this happen? To start with, know that your sink and washing machine drain lines tend to run congruent to each other. This means they combine at some point on the way to the main sewer line. So, if there is a problem after they combine, it can affect both systems.

How to Fix the Problem

First, you must pinpoint the problem. More often than not, a washing machine backup will occur in one or more sinks during or after the drain cycle of your washing machine. This may not happen every time or it may get progressively worse. It depends on why it is happening in the first place.

If the sink doesn’t back up on its own when you do the dishes or run the faucet, the clog is probably deeper in the pipes and only responds to the large volume of water being drained from your washing machine. In either case, you probably have a clog in the drainage pipe after the two combine.

Do NOT use any chemicals to clear the clog. Not only do chemicals cause damage to your pipes, which can lead to cracks and leaks later, they are not always effective at actually removing the problem – they simply minimize it in the short term.

To solve the problem, you’ll either need to plunge the sink and hopefully clear out the clog or have someone snake the line to pull the clog out of the drain pipe. If you cannot clear it on your own, it may be a good time to call a North Vancouver plumber for a more in-depth attempt to fix the problem.

Tags: , , ,
Posted in Plumbing | Comments Off

Surrey Drain & Sewer Guide: What You Can Do to Prevent Problems in Your Drains

Wednesday, January 11th, 2012

When you look at a drain in your Surrey home, it seems fairly simple. You pour things down and they disappear into the ether, never to be seen again. Of course, that logic goes out the window the second the drain starts to backup or overflow. There are things you can do to avoid such problems though and most of the time, they cost nothing and take only a few minutes a week.

Simple Household Drain Maintenance

The first step to avoiding a problem is not putting anything down your drain that might cause said problem in the first place. Specifically, avoid grease, food, or other objects that might build up in your drains if not properly disposed.

Food can be broken down by a garbage disposal or, even better, placed in a compost pile. Grease, however, should never enter your sink at all. Pour all old kitchen grease into a coffee pot or bucket and dispose of it carefully. It can be thrown away in some places, or it can be recycled. Whatever you do, though, don’t pour it down the drain.

Another easy tip to keeping those drains clear is to pour a natural compound down every now and then like dishwashing liquid or baking soda and vinegar. Expensive drain cleaners are not only unnecessary – they are unsafe for the person using them and can cause damage to the pipes if you are not careful. To avoid such damage, stick with hot water based compounds and vinegar. The key is to do it preventatively.

If you wait until a full blown clog occurs, baking soda and vinegar may not get the job done and you’ll need to call a Surrey plumber who has a snake or other equipment to get the clog out.

Professional Maintenance

While regular flushing of your drain with hot water and vinegar allows you to clear out the vast majority of the stuff that builds up there every week, it’s also a good idea to call a Surrey professional for annual maintenance. Such annual maintenance involves visual inspection, professional grade clearing of food and waste products and a full flush. Done properly, this will minimize the cost of future repairs and replacements and keep your plumbing running smoothly for years to come.

Tags: , , , ,
Posted in Plumbing | Comments Off

Vancouver Plumbing Repair- Another Happy Customer!

Friday, January 6th, 2012

When you are hiring a plumbing company, you don’t just want someone to fix your problem, you also want someone who will be respectful of your home and any questions you might have. With plumbing repairs especially, you want to make sure the problem is fixed the first time. A good technician will not only fix the problem quickly but also make sure that you have no other issues that will cause trouble in the future.

At Milani, we make sure that all our technicians do their best on every job. Our goal is to exceed your expectations and make sure that you are completely happy with your experience with us. Here is what a customer in Vancouver called to say about his experience with one of our technicians:

I just wanted to say what a great worker Winston is, he did an amazing job. Hardest worker I’ve ever seen. Went above and beyond and I am extremely appreciative for his hard work!

You’re welcome! We are glad that you had such a good experience with our team. Remember that it is always better to address problems early, water damage can be expensive and inconvenient to repair!

Tags: , , ,
Posted in Plumbing | Comments Off

North Vancouver Plumbing Problems You Can’t Fix Yourself

Friday, December 9th, 2011

While there are some relatively simple plumbing repairs that most North Vancouver homeowners can handle with ease, there are some plumbing problems that have a significantly higher degree of difficulty.

For these trickier or more extensive jobs, you really need to call in a plumber. What kinds of projects are we talking about here?

Take for example a simple clogged drain. Whether it’s your tub or your kitchen sink, you’ve certainly encountered a clog over the years. Sometimes they are simple and easy to deal with, so you decide to tackle it on your own. First, you pour some commercial chemical drain clearing product down the drain. You let it sit for a while, like the instructions say, then run the water.

No luck—the drain is still clogged.

So, you try a pipe snake. You thread it down into the drain and through the pipe until it hits the clog. Then you pull back and…nothing. So you try again and again, really jamming the snag down in there to make it engage the clog, until…it breaks.

Now you’ve got a clog and a broken pipe snake in there.

So, you try more drain cleaner, but of course it doesn’t work again, and now the harsh chemicals are taking a toll on your pipes. You decide to just take the length of pipe out so you can see the clog, then remove it. Soon, you find yourself in over your head and you’re not sure how to replace the pipe.

Yikes. That’s a mess.

This isn’t to say you should never attempt to a plumbing repair on your own. Sometimes they are simple enough that the DIY option is the cheapest and best. However, if your efforts are coming up short and you’re about to enter unfamiliar territory, call in a pro. It will save time, money and headaches in the long run.

Tags: , , ,
Posted in Plumbing | Comments Off

The Do’s and Don’ts of Clogged Drains: A Guide from a Burnaby Plumber

Friday, December 2nd, 2011

Clogged and slow drains in your home can be a real bummer. Water standing in the kitchen sink is gross, and no one likes to shower with the tub gradually filling around their feet. Calling a Burnaby plumber when the clog gets out of hand is easy enough, but it’s  even easier to prevent them from forming in the first place.

With proper use, some brief regular maintenance and a few tricks, most clogs can be stopped dead in their tracks before becoming a problem. Follow these guidelines and you may never need to make that emergency plumber call again.

Don’ts

First of all, there are some things you just shouldn’t do to your drains and pipes. These things can quickly lead to clog buildup, so avoid them:

  • Don’t pour liquid grease, such as bacon grease, down drains. It can solidify in the pipes and cause a clog.
  • Don’t flush anything down the toilet that is not designed to be flushed.
  • Avoid using bleach or other chemicals to clean tubs, sinks and drains. Particles from these cleansers can build up to cause clogs, or even erode pipes.

Do’s

Even with best practices, no drain will remain completely clean. However, a little proactivity can stop everyday residue from accumulating and forming a nasty clog. Try some of these maintenance tips to keep things running smoothly:

  • Use a screen, guard or trap. These can catch food, hair and other debris which would otherwise wind up sitting in your pipes.
  • Clean sink and drain stoppers regularly. Debris can get trapped on and under the stoppers, just waiting to break loose and cruise into the drain to cause a clog.
  • A few times a year, stop up your sinks and tub, fill them up all the way, then let them drain. The pressure and volume of the water will help shake loose deposits in the pipes.
  • Once a month or so, carefully pour boiling water down the drain to dislodge stubborn deposits. You can also do this any time you notice a drain is starting to run slow. Vinegar is also effective.

Tags: , , , ,
Posted in Plumbing | Comments Off

How to Increase Your Water Pressure: A Guide from North Vancouver

Friday, November 25th, 2011

It’s no fun when you are in the middle of taking a shower in your North Vancouver home and the stream of water slows to a trickle. The most logical thing to blame the loss of water pressure is a toilet being flushed or a washing machine being filled. It is not uncommon for losses in water pressure to be associated with simultaneous water usage in other parts of the home.

But if low water pressure seems to be a constant problem when only one source is being used and there are no other appliances using water at the same time, you may have a bigger problem on your hands.

The first thing to do is to check the source of the water supply to your outdoor faucets. Turn the hose bibs to the fully open position and run the water. Is the pressure okay? If so, you probably have a problem indoors. While you are outside, check for any leaks in the hose bibs or faucets. A leak can cause a loss of water pressure in other plumbing circuits.

Now check the hose bibs on the lines leading to interior fittings, like faucets or showerheads, etc. Is the hose bib turned to the fully open position? Someone may have been playing with the bib and turned it down or off. If that checks out okay, take a look at all of the fittings in your plumbing fixtures. Are there any leaks? Is there standing water anywhere, indicating a leak?

If so, tighten up the affected fittings. If you need to remove any fittings to inspect or replace (i.e. a worn out washer or bushing), make sure you turn off the water supply to the fitting first.

If there are filter screens in your faucets check them for an accumulation of debris and clean if necessary. A clogged screen can greatly reduce water pressure.

Many new homes now come with a pressure regulator, which governs the water pressure going into the home. The regulator is located above ground, usually where the pipes enter the home. The pressures are usually preset by the regulator manufacturer but may not always be compatible to the local environment. If you think that may be the problem, contact a local plumbing professional for an opinion.

A disruption in the piping that feeds water into the home can also affect water pressure, such as tree roots in the pipes or a break in the line. These problems can only be diagnosed and corrected by qualified plumbing professionals. Please do not attempt to find and fix these problems as the result may be costly or even dangerous to your health.

Low water pressure can be a drag but it may also only require a quick fix.

Tags: , , , , ,
Posted in Plumbing | Comments Off

« Older Entries