Posts Tagged ‘Port Moody’

What Happens When You Neglect Heat Pump Maintenance in Vancouver

Wednesday, February 1st, 2012

Just like any HVAC system in Vancouver, the heat pump in your home needs routine maintenance and yearly check-ups to operate as efficiently and safely as possible. You also don’t want your heat pump to wear down to the point of a major malfunction or breakdown, which can be costly to repair or may require a complete heating system replacement.

Here are some things that could go wrong and cost you a lot more in the end if you don’t keep up with the regular maintenance of your heat pump.

Damage to the Compressor

The compressor in a split-system heat pump works whether you are heating or cooling your home. In the winter, the compressor reverses the flow of the refrigerant to defrost the outdoor coils, and in the summer it supplies the refrigerant to cool the home, as well as cooling the outdoor coils. Proper airflow is vital to keeping the compressor running smoothly. Filters that are not changed regularly, dirty coils, and dirty fans can all restrict airflow, which will damage the compressor. Debris around the outside components should also be cleared to allow proper airflow.

Decreased Efficiency

When dirty or broken components restrict the airflow, this damages the compressor and decreases the heat pump’s efficiency levels.  Not only is it important to clean your heat pump regularly, but you should also have it checked by a certified heating technician once a year. This will also prevent safety hazards and other hidden issues with the heat pump.

Improper Refrigerant Levels

Most heat pumps are charged with refrigerant at the factory; however, if models that are charged when they are installed are not given the right amount of refrigerant this can also affect performance levels. Refrigerant leaks and other common problems can be prevented by scheduling an annual maintenance visit with one of our qualified technicians.

Don’t wait until the heat pump in your home stops working, call to schedule your yearly check-up.

Tags: , ,
Posted in Heat Pumps, Heating, heating system replacement | Comments Off

Heating System Preventative Maintenance: Some Pointers from New Westminster

Friday, November 18th, 2011

While heating systems in the past consisted of wood burning stove and fireplaces requiring little maintenance, today’s sophisticated furnaces and building controls in New Westminster require a good dose of preventative maintenance in order to avoid mechanical failures and inefficient operation.

For example, a furnace runs better and lasts longer when you maintain a regular schedule of filter cleaning or replacing. A dirty or clogged filter can restrict airflow from the furnace into your home’s ventilation system and cause the furnace to work harder, putting more wear and tear on it and taking months, if not years, off of its useful life. If your furnace uses disposable filters, check them every month and replace them if necessary. If your furnace uses an electronic filter that requires cleaning, check it on a monthly or semi-monthly basis and clean it with soapy water and a hose. Be aware of the change of seasons which could add extra pollutants into the air like pollens, ragweed, and cottonwood. This debris easily finds its way into the filters and creates an unhealthy indoor environment.

You can also perform a simple visual inspection of working components inside your furnace by removing the access cover and checking – with a flashlight – for loose fan belts, frayed electrical wires, or a build-up of dirt and dust. Simple solutions include tightening or replacing belts, repairing wiring, and vacuuming out dirt and dust with a hose attachment. All of these actions will keep your furnace working better and prevent future failures.

You can also do a visual check of your home’s ventilation system, paying close attention to any cracks in duct seams or holes in flex ductwork. Using sealing cement or duct tape can usually fix these problems and allow for better, unrestricted air flow. Again, these actions will help your furnace work more efficiently and avoid premature failures.

Maybe the best advice for preventing heating system breakdowns is to have a regular maintenance schedule with a local qualified heating contractor. Most contractors can set you up with annual furnace and ventilation system inspections. Having a service agreement – as a rule – gives you priority emergency repairs and discounts on parts and services. Besides that, planned maintenance is also preventative maintenance, something that will give you peace of mind in the long run.

Tags: , , , ,
Posted in Heating | Comments Off

How Heating Zone Control Can Save You Money in Vancouver

Wednesday, November 9th, 2011

The costs of heating your Vancouver home have risen dramatically over the past couple of decades, thanks to higher energy costs and price increases for heating equipment. Despite the strides made in energy efficiency, there seems to be no end in sight for the steady rise in heating equipment operating costs.

Now add in the cost of heating unoccupied areas of your home, such as basements, hallways, or extra bedrooms, and the energy costs go even higher. Most of these costs are unnecessary and avoidable if you have the time and a small investment in a well-planned heating “strategy” for your home. This strategy involves using heating zone controls to make the most efficient use of your heating system.

In a nutshell, here is how heating zone control works. The rooms in your home are connected to your heating system by a series of ductwork, which carries heated and conditioned area to all corners. But some of these areas may not need to be heated as much – or possibly at all – compared to other rooms in your home. For example, do you need heat in your kitchen but not in your basement? Most people would answer yes. Or they may say they need more heat in the kitchen and some, but not very much heat in the basement.

Or try this: do most people in your house spend more time in one room, such as the family room, and less time in their bedrooms? If so, why would it be necessary to heat the bedrooms all of the time? In order to deliver heat to areas in your home that need it the most, the ductwork to these rooms should always be “open.” Ductwork to other unused areas of your home can be “closed” during various times of the day.

Opening and closing of ductwork and airflow is achieved by zone controls. A zone control is installed in the home which electronically or wirelessly opens and closes “dampers” in the ductwork, depending on the heating demand. You can divert heat to areas of your home using zone control and dampers while decreasing the heating load on your furnace. This type of heating zone control will move heated air to where you want it. Simply put, you are not heating areas of your home that don’t need the heat.

The heating zone controls can be programmed for various times of the day, too. For example, you may not need any heat in your basement while you sleep or when you are away from home. You can program the damper in your basement’s ductwork to remain closed or partially open during these times. In a sense, the heating zone control in your home acts like a programmable thermostat – only it uses a series of dampers to control indoor temperatures.

The next time you walk into an unused part of your home, think about how much money you are spending to heat it. It makes sense to consider heating zone controls. The initial costs of installing zone controls and dampers are minimal and the payback in energy savings and comfort are substantial.

Controls save you money.

Tags: , , , , ,
Posted in Heating | Comments Off

Why is My Furnace Turning On and Off? A Question from Vancouver

Monday, October 24th, 2011

One of the most annoying things your furnace can do in your Vancouver home is to constantly keep turning on and off. This on-off cycling keeps your home from heating up properly. This action – called short cycling – also requires more electricity and drives up utility bills.

Short cycling is caused by an overheated furnace, which triggers safety mechanisms and shuts down the furnace. After a brief interval and cooling down, the furnace starts up again the cycle keeps repeating itself. Not only is it an annoyance, it can also signal more serious problems. A leaking heat exchanger can cause a furnace to overheat – and produce deadly carbon monoxide gas.

If a furnace is working too hard and overheating, it is usually because of airflow in and out. Think of the furnace as a human heart. If there is a blockage in the veins and blood flows slowly, a heart has to work harder to pump blood around or through the blockage. Your home’s ventilation system needs to be clear of dirt, dust, and debris. The more blockage in your ductwork and vents, the more friction is created, slowing down airflow and ultimately ending with an overworked furnace that continues to cycle on and off. And a blocked exhaust vent, such as a chimney or dedicated exhaust vent, can also cause a furnace to work harder. Check for things like leaves, dead animals, or bird’s nests.

The blockage may also be coming from a clogged furnace filter. You should clean or replace your furnace filter after a visual inspection reveals any type of build-up of dust or dirt. Do this at least every three-six months.

If you have a two-speed fan on your furnace, it is recommended that you run the fan in low speed during the cold months and high speed in the warm months. The reason? Warm air is lighter and takes less force to move.

There are other measures to take to prevent short cycling but these usually require a professional heating and cooling service technician to correct the problem. If in doubt, call your contractor and schedule a furnace inspection. Don’t make your furnace work any harder than it was designed for – and keep your home’s occupants comfortable and safe.

Tags: , , , , , , ,
Posted in Heating | Comments Off

When Should You Replace Instead of Repair Your Heating? A Question from Anmore

Wednesday, October 12th, 2011

We all dread an expensive repair in Anmore, whether it is a car that needs a new transmission, a leaky roof that needs new shingles, or electrical wiring that has been chewed up by a wild animal. Equipment repairs are a necessary evil. We often try and put bandages on things that we know should be replaced but we just can’t afford to replace them.

The same can be said about your home’s heating system. When your heat goes out or your home just doesn’t seem to be heating up to the setting on your thermostat, your first inclination is to check and see if it is running. Some people will put their hand over a heating vent to check for hot air while others may go into the basement or mechanical room to listen to hear if the furnace is running. Maybe there is a blockage in the ventilation system or a blown circuit breaker, two relatively easy fixes.

If the furnace isn’t working after checking the obvious symptoms, your next move is to call for service. Any qualified heating professional would be able to diagnose your problem and offer suggested repairs. Something relatively minor like a bad circuit board or blown fan motor are not real expensive repairs and are the best option versus replacing the furnace. And you may keep experiencing the same problem and getting the same repair work done – anything to avoid an expensive replacement.

But at some point the vicious cycle will come to an end. Your repair bills will begin to inch their way past the cost of replacing the furnace. You can only bandage a problem so long before it becomes “unfixable.” You may not want to pay an expensive replacement bill but consider the alternatives.

First is the obvious – it costs too much to keep repairing the furnace. Secondly, you never know when the furnace may break down and its failure to operate could have dangerous effects on the people in your home, especially if someone is sick. Third, your furnace may not be able to keep up with the heating demand due to lifestyle changes, i.e. an addition put on the house, carpeting removed and wood floors exposed, a new window, door, or skylight added, etc. Your old furnace may not have been designed to keep up with these changes and the repairs are only delaying the inevitable.

Ask yourself if everyone in your home is comfortable during cold weather. If most answer no, it may be time to consider replacing that old furnace with a new, energy efficient model that uses today’s technology – and leaves a smaller carbon footprint – to keep up with the demand for heat, in any sized building or home. Your decision to replace your old heating system could be as simple as the need to use modern technology to solve your indoor comfort problems.

Tags: , , , ,
Posted in Heating | Comments Off

What to Do if Your Heating System Breaks: A Guide From Rosedale

Monday, October 10th, 2011

What if the heart of your Rosedale home’s heating system – the furnace – stops working? The warm air that used to flow from your vents has been replaced by a chilly draft. It isn’t time to panic, but it is time to take action. Before you do anything, determine why the furnace stopped working. It may be something as simple as a tripped circuit breaker in your electrical panel. Check the circuit breakers first.

The pilot light in your furnace may have blown out. It can be re-lit if you follow the directions in your furnace owner’s manual. You can find answers on how to re-light a pilot light on the Internet, too.

If the shutdown has not been caused by an electrical or pilot light failure, there is still no need to panic. But another obvious question is: did you pay your last gas bill? Maybe you had a shutoff notice and either ignored it or forgot about it.

Now that you are convinced that the furnace has pooped out, here are some things you should do. First, find the name of a qualified heating and cooling professional. If you already use a heating contractor, contact them and schedule a service call.

While you are waiting for help to arrive, ensure that everyone is safe and accounted for. Make sure pets are nearby and protected from the cold, too. What you don’t want to do is use any appliance to keep you warm that is not designed to keep you warm, like a stove. If you have electric space heaters or propane heaters, carefully locate them in a well vented room (windows open a bit or portable fans circulating air). You don’t want any build-up of gases from fossil burning appliances, gases which could contain deadly carbon monoxide.

Huddle up everyone into a room and break out lots of blankets. You may even want to make an “adventure” of this – find a movie to watch and pop up a bunch of popcorn.  If your waiting time is more than 24 hours, you might want to call up a friend or relative and make arrangements to spend the night with them.

The main thing to remember is not to panic. Most qualified heating contractors, knowing the circumstances, will send out a repair person in a matter of minutes or within one or two hours. Just remember to avoid keeping warm by using unvented heating devices.

Tags: , , , ,
Posted in Heating | Comments Off

What Is a Whole House Pressurization Test and Should I Get One?

Monday, July 4th, 2011

If you have a forced air heating or cooling system in your home, you also have a system of ducts through which that heated or cooled air circulates. And most people don’t give a second though to those ducts. After all, if your heating and cooling systems are working, the ducts must be doing their job, right?

Unfortunately, that’s not always the case. If ducts are not working properly, the whole system will be in trouble, even when you don’t realize there is a problem. That’s why a pressurization test is so important – it provides peace of mind knowing that your home’s ductwork is not only properly installed, but that it doesn’t need any special repairs.

Why Pressure Matters

Your duct system depends on proper pressurization to evenly and efficiently distribute air throughout your home. Leaks, cracks or clogs in the system can disrupt that pressure and lead to uneven or inadequate movement of air through your ducts. This causes problems you may not notice, so if you haven’t had your ducts checked for proper pressure in a while, it’s worth looking into.

Improper pressurization causes symptoms like hot or cold spots in your home or an overall drop in the effectiveness of your home heating and cooling system. When loss of pressure is due to a leak that lets in unfiltered air from outdoors it can also lead to a decrease in indoor air quality. Often these symptoms are easy to ignore. But by doing so, you only allow the situation to get worse.

A whole house pressurization test is the best way to determine the state of your home duct system. By using high tech diagnostic equipment, home HVAC professionals check over your entire system to determine whether you have a pressurization problem. If so they can then quickly pinpoint the source. Once that’s done, the repairs are usually quite simple and you’ll get much more out of your home heating and cooling system than you did before.

Even if no symptoms of improper pressurization in your ducts have presented themselves, it’s worth having one of these tests performed. Especially if you don’t know when the system was last checked, a whole house pressurization test can help uncover small problems before they turn into bigger ones. And the peace of mind this provides is well worth the day it takes to perform the test.

Tags: , , ,
Posted in Indoor Air Quality | Comments Off

Green Your Plumbing

Monday, January 24th, 2011

These days, “green plumbing” is getting increasing attention, especially in dry areas like the southwestern US.

“Green plumbing” helps the environment by doing one or more of the following:

  • Saving water
  • Saving energy
  • Using environmentally-friendly materials

There are a wide range of green plumbing products that can make a big difference in how much water and energy your home uses. They range from simple accessories that cost less than $20 to major home remodels. Here are a few of them, ranging from the simple and immediate to larger investments with a longer-term payback.

  • Low-flow showerheads and faucet accessories (often called “aerators”). Check the side of your current faucet and showerhead to see if they use more than 1.5 GPM and 2.0 GPM, respectively. If they do, you can benefit from an upgrade. Look for the EPA WaterSense label to be sure that your new showerheads and faucet accessories are water-efficient.
  • Hot water heater blankets and pipe insulation.You don’t need to insulate your hot water heater and  pipes to prevent freezing, but doing it will save money, water, and energy, and (as a bonus) you’ll enjoy hotter showers in the winter. This is a simple DIY job and the materials are extremely affordable.
  • Touch-free faucets. When you’re not actively using them, touch-free faucets shut off. According to industry estimates, the result can be a water savings of up to 70%. Touch-free faucet technology has improved greatly in recent years, and sensors are now very reliable. If you like your current faucet and want to keep it, there are also touch-free faucet conversion kits.
  • Dual-flush toilets. As the name suggests, these toilets have two different flushes: a “half-flush” for liquid waste, and a “full flush” for solids. Dual-flush toilets are standard in many European countries and are becoming increasingly popular in the U.S. because of their water-saving potential (up to 68% over conventional toilets) and sleek styling.
  • Tankless water heaters. Unlike conventional tank heaters, which use energy constantly to maintain a reserve supply of hot water, tankless heaters only use energy when hot water is needed.  Tankless water heaters are not quite “instantaneous”, as some manufacturers claim, but they provide hot water within a few seconds. Good quality heaters can provide hot water to multiple fixtures simultaneously.
  • Sprinkler system upgrades. Much of the water from spray sprinkler systems evaporates. Trickle and drip irrigation systems can improve water efficiency by delivering smaller amounts of water directly to the base of the plant. Other products, such as pressure regulating spray heads and rotors and automatic rain sensors, can also save thousands of gallons a year. Another option is to re-use laundry waste water by diverting it into the garden. This can be a DIY project or can be built directly into your plumbing. Check with your local authorities to find out if this is permitted in your area.

Tags: , , , , ,
Posted in Plumbing | Comments Off