Posts Tagged ‘Yennadon’

Unclog a Floor Drain in Deroche: Complicating Factors

Monday, August 1st, 2011

It is never fun to wander down into your Deroche basement only to find that your floor drain has backed up. This is not a situation that will take care of itself and you want to get it under control as quickly as possible. While there are certainly plenty of things you can do to try and unclog a floor drain on your own, there are quite a few potentially complicating factors to consider as well.

First of all, you should make sure that no one in the house turns on any running water for anything until the drain has been unclogged. The floor drain in your basement is usually the last stop on the line for all of the water used in your house, and so any running water anywhere above will only cause more water to back up in the basement. Of course, if you cannot use any running water anywhere else in your house, it is even more imperative that you are able to unclog the floor drain quickly.

If you happen to have a snake on hand, this may be the best option to try first. However, it can be a bit difficult to get the snake to make the sharp turn typical of these types of drains not long after the pipe descends below the floor. That is not to say that it cannot be done, but you should be aware that you need to make sure the snake turns the corner before it will be useful to you at all.

If you do not have a snake of your own, you may still be able to take care of the blockage without calling in a professional plumber. But first you have to find it. Depending on the layout of your drainage system, this may be easier said than done. You can also make a pretty big mess if you open up various sections of pipe looking for the blockage, so be aware and make sure you have something in place to catch the runoff and debris that may come out of the pipes when you open them.

You may also run into trouble if the blockage is actually outside of your house in the larger sewer line that runs to the street. Unclogging a drain with this type of problem is generally a job for a professional and there is very little you will be able to do on your own.

Tags: , , , ,
Posted in Plumbing | Comments Off

How a Water Softener Works

Wednesday, July 20th, 2011

You use water for many things. It is necessary for bathing, cooking, washing clothes and for drinking. But the water we use in our homes is not pure. It has plenty of other minerals and additives suspended inside. While some of these, like fluoride, are intentionally added to the water supplies in certain areas, some others get in by chance.

Aside from actual pollutants, the additives you may be the most concerned about finding in your water are calcium and magnesium. These minerals are picked up by water as it moves through the ground, and the more of them that get into your home water supply, the harder that water will be.

The term hard water is used to describe water with high levels of calcium and magnesium present. These minerals are not actually dangerous to us, but they can cause all sorts of problems for your indoor plumbing and other household systems. For instance, hard water will leave deposits of these minerals on the insides of pipes and on sinks, faucets and bathtubs.

Residue will also build up in appliances like coffee makers, dish washers and washing machines. Over time these buildups can become a real problem and you may have to pay for costly repairs or need to replace large appliances.

In order to avoid these types of complications, your best bet is to have a water softener installed. These systems can be connected directly to your home water source and they are able to remove excess calcium and magnesium from the water before it ever reaches any of your indoor plumbing or appliances.

Water softeners generally remove these minerals by attracting the positively charged calcium and magnesium particles with a tank full of negatively charged polystyrene particles. In this system, the calcium and magnesium are replaced by sodium ions as they move through the water softener, thereby maintaining the overall balanced composition of the water. Once the water has passed through and the calcium and magnesium have been left behind, the water softener will flush them out and prepare to absorb another wave of hard water minerals.

Tags: , , ,
Posted in Plumbing | Comments Off

Types of Drinking Water Filters

Monday, June 13th, 2011

There are not many things more important than making sure that your home drinking water supply is safe and free of contaminants. All kinds of things can appear in your drinking water, and it is helpful to know exactly what types of contaminants are prevalent in your area so that you can make the best decision about what type of water filters to buy.

Some water filters work well at removing certain types of contaminants but not others. However, there are some good water filters that can get rid of almost all contaminants on their own. One such type is a distiller. Water distillers operate by heating the water coming into your home until it turns into steam. When water evaporates like this, it leaves behind anything it was carrying with it when it was in liquid form. The steam rises and moves into another chamber, and when it condenses back into liquid form again, the contaminants are no longer present.

Another type of water filter that removes the majority of contaminants is a reverse osmosis filter. These are excellent for removing things like asbestos, minerals, metals, salts and nitrates. For best results, however, you will want to purchase a system that incorporates some type of carbon filter as well. Carbon filters, placed either before or after the osmosis filtering system, are better at removing things like pesticides and radon. The combination of these two water treatment types into one filter system makes the solution more complete.

If you do not think you have a serious contamination problem but just want to get rid of bad tastes or smells in your water, activated carbon filters are a good and economical choice. However, you will want to make sure that you know exactly what contaminants the filter you purchase is designed to remove, as not all carbon filters are equally as effective against certain types of contaminants.

The most important thing to do before you go out and purchase a water filtration system, however, is to determine what exactly you are trying to remove from your water. The types of contaminants found in your water will vary a great deal depending on where you live and what types of pipes you have in your home, and that will directly affect the type of water filter that is right for you.

Tags: , , , ,
Posted in Plumbing | Comments Off

How Bad Is the Air in Your Home?

Wednesday, April 13th, 2011

Every day you hear about another awful contaminant that can get into your home’s air supply. Radon gas. Carbon Monoxide. Nitrogen Dioxide. Smoke. Mold. The list gets longer with each passing year and many homeowners are understandably worried. However, before you run out and by the newest lineup of filters, purifiers, and UV lights, stop and think about just how bad your indoor air actually is.

When Was Your Home Built?

Homes built in the last 10-15 years tend to be well ventilated and may even have air quality systems already in place. It’s those built in the late 1970s and early 1980s that tend to have the worst ventilation (assuming they have not been updated since then).

This kind of poor ventilation can be dangerous, but usually only in that you have less fresh air and more indoor allergens and contaminants. Specifically, you’re most likely to suffer from things like pet dander, dust, pollen, and dirt in the air. On their own, these are not dangerous, but without fresh air to circulate them outside and ensure you get a steady, clean supply of air to breathe, they can make you ill.

How Bad Can It Get?

While it’s rare, some homes suffer from more advanced contaminations. The most common is mold. Mold grows primarily in dark, damp spaces. If your humidity levels get too high in the summer, the ductwork in your house is perfect for mold and it will blow the spores directly into your air, putting everyone at risk.

You should also be wary of exhaust fumes from your appliances that may not get properly removed from the house. Both of these problems can be fixed with regular duct and exhaust cleaning.

Outdoor contaminants can also make it into your indoor air. Things like exhaust and smoke, gas, radon, or other outdoor pollutants should be tested for when you setup a new indoor air quality system. There are filters and purifiers that will remove almost all of these contaminants, but they are not always required, so you should check before making a decision.

Ultimately, the odds are that your home suffers only from some stale, dusty air. But, it is very important to keep everything clean and test it regularly to make sure nothing worse develops. Poor air quality is about more than just comfort – it’s an honest health issue.

Tags: , , , ,
Posted in Indoor Air Quality | Comments Off

Attic Insulation – Does it Save You Money?

Monday, April 11th, 2011

While you may not spend too much time up in your attic in the winter – or at any time of year for that matter – the conditions up there can wind up having a significant impact on the size of your heating bills. Fortunately, if you’re leaking heat out of your attic like crazy, there is something you can do about it. And it won’t even take you a lot of time or cost too much, but it will wind up saving you a ton of money in the long run.

So what is it that you can do to magically save so much on your heating bills? Well, the truth is that all you really need to do is insulate your attic properly. Since the attic isn’t typically a space that people occupy often, builders often leave these areas uninsulated. That means that they’re pretty cold in the winter. But if you’re not sitting up there, does it really make any difference?

Absolutely it does. The problem with having an uninsulated attic is that heat rises and so will quickly move to the highest point in your home. This is the attic, of course, and if the attic isn’t insulated, all of that warm air that you’ve been paying to heat will go right out the top of your house. Even if the door to the attic is shut up tight, you will still be losing heat into it.

And if the attic isn’t insulated, chances are that there’s no insulation anywhere above the ceiling of the top floor of your house. With heat continually rising and escaping out of the top of your home, you’ll find that your home heating system has to work much harder to keep the house at a comfortable temperature. And the harder your heating system works, the more you’re paying in energy bills each month.

Fortunately, adding insulation to your attic is relatively easy and won’t cost you much at all. And the savings you start to see immediately on your energy bills will more than make up for the expense of having the insulation installed. Even if your attic does have some insulation in place already, it may be worth checking to make sure it’s still working well. Some types of insulation simply break down over time and you might not be getting anywhere near the protection you thought you were.

Tags: , , , , ,
Posted in Heating | Comments Off

Maintenance Really Does Save Money

Monday, March 21st, 2011

When it comes to your home heating and cooling systems, you really cannot go wrong with proper annual maintenance. While it may seem like an unnecessary expense, especially if your systems are relatively new, you will save a lot in the long run if you pay that small fee once a year for each system.

During a maintenance visit, a technician can thoroughly clean out your heating or cooling system and check all parts to make sure they are not showing signs of excessive wear and tear. If they do find a problem or a part that needs to be replaced, they will be able to make the necessary repairs quickly and you will not have to worry about calling someone out later for an emergency visit.

Also, catching problems early like this means that repairs will likely involve fewer parts and cost much less than they would if you let the problem go and it became more widespread. The truth is that your heating or cooling system can continue to work when one or another of its parts is not working correctly, but that means that other parts of the system have to work overtime to create the same result.

Your heating or cooling system will also be much more energy efficient if it receives regular tune ups and attention from a professional. Even the best new systems lose a small percentage of their efficiency each year that they are in operation. While this is not much from year to year, the cumulative effect will soon cause your energy bills to climb higher than necessary.

Paying for regular maintenance, then, can actually save you money because it will mean you pay less each month to run your system. And it is never too late to start. Even if your heating or cooling system is not new, it will benefit from a thorough cleaning and tune up. You may be quite surprised how much your energy bills go down after this type of service has been performed.

Annual maintenance can also help you to get more for your money by extending the useful life of the heating or cooling system. Many systems that are properly maintained can last even beyond their expected life span, meaning that you will not have to replace it as soon as you would have otherwise. For all of these reasons, the minimal cost of an annual maintenance visit is well worth paying over the long term.

Tags: , , , ,
Posted in Maintenance | Comments Off

Heat Pump Noise Considerations

Wednesday, February 23rd, 2011

If it is time to think about replacing your home or office heating system, there are a few issues to contemplate. Perhaps you have made the wise decision to install a heat pump. Price is a serious concern, as well as the choice of an installer for the unit. However, there is an issue that sometimes gets overlooked. The noise factor of the new unit is sometimes not considered at all.

The good news is that modern heat pumps are now made in such a way that noise is kept to a minimum. For the most part, new models are far quieter than the older ones used to be. While the new units provide the same or greater amounts of heating and cooling, the noise level has been reduced to a fraction of earlier models.

The outdoor portion of the heat pump system is the only part that makes any noise. If this unit sits near a window, there is the slight possibility that a small amount of noise will be heard. Chances are, though, that anyone inside the home or office building will barely notice at all that the heat pump is running. Because of research, ingenuity and modern design, new heat pumps now on the market are among the quietest that have ever been made.

Vibration of the outside unit has been mostly eliminated, creating a unit that practically purrs. The tweaking and adjusting in design and manufacturing combine to make heavy vibration a thing of the past. The amount of noise generated from newer heat pump units is often compared to the small amount of noise you would hear from your refrigerator.

If the noise emitted from the outside portion of a heat pump causes any issues with a neighbor, it is possible to install sound panels that will help absorb the sound. Panels of this type should be weatherproof to withstand outdoor extremes. Thankfully, the problem of loud noise pollution from a heat pump’s outside unit is mostly a memory from a bygone era. With modern technology and proper placement, this type of problem has gone the way of the dinosaur.

Tags: , , , , , ,
Posted in Heat Pumps | Comments Off

Attic Insulation – Does it Save You Money?

Wednesday, January 12th, 2011

While you may not spend too much time up in your attic in the winter – or at any time of year for that matter – the conditions up there can end up having a significant impact on the size of your heating bills. Fortunately, if you’re leaking heat out of your attic like crazy, there is something you can do about it. And it won’t even take you a lot of time or cost too much, but it will save you a ton of money in the long run.

So what is it that you can do to magically save so much on your heating bills? Well, the truth is that all you really need to do is insulate your attic properly. Since the attic isn’t typically a space that people occupy often, builders often leave these areas uninsulated. That means that they’re pretty cold in the winter. But if you’re not sitting up there, does it really make any difference?

Absolutely it does. The problem with having an uninsulated attic is that heat rises and so will quickly move to the highest point in your home. This is the attic, of course, and if the attic isn’t insulated, all of that warm air that you’ve been paying to heat will go right out the top of your house. Even if the door to the attic is shut up tight, you will still be losing heat into it.

And if the attic isn’t insulated, chances are that there’s no insulation anywhere above the ceiling of the top floor of your house. With heat continually rising and escaping out of the top of your home, you’ll find that your home heating system has to work much harder to keep the house at a comfortable temperature. And the harder your heating system works, the more you’re paying in energy bills each month.

Fortunately, adding insulation to your attic is relatively easy and won’t cost you much at all. And the savings you start to see immediately on your energy bills will more than make up for the expense of having the insulation installed. Even if your attic does have some insulation in place already, it may be worth checking to make sure it’s still working well. Some types of insulation simply break down over time and you might not be getting anywhere near the protection you thought you were.

Tags: , , , , , , ,
Posted in Energy Savings | Comments Off